Jampot Outer Tube - Too Far Gone? (1955 18CS)
-
- Posts: 37
- Joined: Wed Jan 09, 2019 6:27 pm
- Location: Kent UK
Jampot Outer Tube - Too Far Gone? (1955 18CS)
Hi,
I'm rebuilding my Jampots.
They were as expected, completely empty of oil and the piston has been grating up and down the outer tube and left a nice lot of aluminium filings at the bottom.
Please have a look at the picture attached. Is this outer tube too worn to reuse?
My feeling is that this wear is going to reduce the smoothness of the action and some oil is going to leak past, reducing the effectiveness of the damper, but not actually leaking to the outside.
Given that replacements are £40 each, I'm thinking I'll rub down the high spots with fine emery paper, rebuild them (with new bushes and seals) and see how it goes.
What does the voice of experience say?
Further to my earlier posts, which were a bit downhearted, The engine is back together with a bottom end rebuild, new cylinder liner, NOS wirewound piston.
Its great! Starts first kick and sounds like a sewing machine. I'm very pleased and fired up to continue the restoration.
Thanks for your help and advice.
Cheers
Matt
I'm rebuilding my Jampots.
They were as expected, completely empty of oil and the piston has been grating up and down the outer tube and left a nice lot of aluminium filings at the bottom.
Please have a look at the picture attached. Is this outer tube too worn to reuse?
My feeling is that this wear is going to reduce the smoothness of the action and some oil is going to leak past, reducing the effectiveness of the damper, but not actually leaking to the outside.
Given that replacements are £40 each, I'm thinking I'll rub down the high spots with fine emery paper, rebuild them (with new bushes and seals) and see how it goes.
What does the voice of experience say?
Further to my earlier posts, which were a bit downhearted, The engine is back together with a bottom end rebuild, new cylinder liner, NOS wirewound piston.
Its great! Starts first kick and sounds like a sewing machine. I'm very pleased and fired up to continue the restoration.
Thanks for your help and advice.
Cheers
Matt
You do not have the required permissions to view the files attached to this post.
-
- Member
- Posts: 746
- Joined: Thu Mar 31, 2005 1:00 am
- Location: BERKS UK
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
Hi Matt, never had this problem but they do look bad inside! By the time you have smoothed those scratches down I would have thought that the bore would be too large. As they are easy enough to remove and rebuild, you have nothing to loose by trying, but perhaps in the meantime you should start looking for a cheaper pair of replacements at autojumbles? Andy
-
- Member
- Posts: 8560
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
Yes, they do look pretty well corroded rather than worn. However, they are 'only' dampers and are of fairly quick action over bumps etc. and not providing any continuous suspension so perhaps they'll still function well enough.
I expect that my Jampots have been dry for years but I never seemed to 'Pogo stick' after encountering bumps.
I've never had a unit apart so I'm ignorant of the details but perhaps refill with a thicker oil than standard.......
I expect that my Jampots have been dry for years but I never seemed to 'Pogo stick' after encountering bumps.
I've never had a unit apart so I'm ignorant of the details but perhaps refill with a thicker oil than standard.......
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Posts: 37
- Joined: Wed Jan 09, 2019 6:27 pm
- Location: Kent UK
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
Thanks for the replies.
I made a sort of honing tool with some tube and emery paper and they don't seem too bad now. The worst of the problem was alloy flakes friction welded to the steel lower bush, which cleaned off OK.
AMC classic spares have a pair of secondhand tubes, which I have purchased. Doesn't seem to be worthwhile going overboard on the refurb as everyone says as suspension units they're not much good even when new.
I have enjoyed working on them and building the tools needed to disassemble them. Pity they don't fulfil the promise of their intricate design.
I made a sort of honing tool with some tube and emery paper and they don't seem too bad now. The worst of the problem was alloy flakes friction welded to the steel lower bush, which cleaned off OK.
AMC classic spares have a pair of secondhand tubes, which I have purchased. Doesn't seem to be worthwhile going overboard on the refurb as everyone says as suspension units they're not much good even when new.
I have enjoyed working on them and building the tools needed to disassemble them. Pity they don't fulfil the promise of their intricate design.
-
- Member
- Posts: 8560
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
I'm probably wrong but I don't think there were so many potholes and crumbling roadsides back in the day.
Making special jigs and tools has also been a large part of my satisfaction when fixing bikes.
Making special jigs and tools has also been a large part of my satisfaction when fixing bikes.
That's what one of my ex-wives used to say about men.Halfwhelk wrote: Pity they don't fulfil the promise of their intricate design.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Member
- Posts: 3369
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: N YORKS UK
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
I rebuilt my jampots a very long time ago. They may have no oil left in them but I've never noticed leaks.
These were probably disguised from the oil leaking forward of the jampots and covering the rear of the Matchless!
If "bounced" when stationary there does seem to be some residual damping.
"AMC classic spares have a pair of secondhand tubes, which I have purchased." Does this mean that the "originals" are not being re-used? I'd keep them anyway.
Johnny B
These were probably disguised from the oil leaking forward of the jampots and covering the rear of the Matchless!
If "bounced" when stationary there does seem to be some residual damping.
"AMC classic spares have a pair of secondhand tubes, which I have purchased." Does this mean that the "originals" are not being re-used? I'd keep them anyway.
Johnny B
-
- Posts: 37
- Joined: Wed Jan 09, 2019 6:27 pm
- Location: Kent UK
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
Johnny,
Please let us know the condition of the bearing surface of your secondhand tubes when you get them. As a newly self-appointed 'expert', I think I can state two truths:
1) All Jampots leak (by now).
2 Any Jampot run for <5000 miles without oil will be scuffed to hell.
Therefore all Jampots are scuffed.
I'll be happy to be proved wrong.
I have found Tru-Blu PTFE liquid thread sealant. (£3.50 from Toolstation) I'm going to try to stop the oil leaking from the threads (at least) when I reassemble mine.
Matt
Please let us know the condition of the bearing surface of your secondhand tubes when you get them. As a newly self-appointed 'expert', I think I can state two truths:
1) All Jampots leak (by now).
2 Any Jampot run for <5000 miles without oil will be scuffed to hell.
Therefore all Jampots are scuffed.
I'll be happy to be proved wrong.
I have found Tru-Blu PTFE liquid thread sealant. (£3.50 from Toolstation) I'm going to try to stop the oil leaking from the threads (at least) when I reassemble mine.
Matt
-
- Member
- Posts: 3369
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: N YORKS UK
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
Hi Matt
I was quoting your thread. I shan't be looking at my jampots for a while. Fixing the timing side bush more important at the moment.
Cheers
Johnny B
I was quoting your thread. I shan't be looking at my jampots for a while. Fixing the timing side bush more important at the moment.
Cheers
Johnny B
-
- Posts: 18
- Joined: Tue Aug 13, 2019 12:29 am
- Location: Punta del Este, Uruguay
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
I put thread sealant when I rebuilt my jampots last year. New seals, bushings, o-rings and new oil.Halfwhelk wrote:Johnny,
Please let us know the condition of the bearing surface of your secondhand tubes when you get them. As a newly self-appointed 'expert', I think I can state two truths:
1) All Jampots leak (by now).
2 Any Jampot run for <5000 miles without oil will be scuffed to hell.
Therefore all Jampots are scuffed.
I'll be happy to be proved wrong.
I have found Tru-Blu PTFE liquid thread sealant. (£3.50 from Toolstation) I'm going to try to stop the oil leaking from the threads (at least) when I reassemble mine.
Matt
Not a single drop leaked ever since.
-
- Member
- Posts: 452
- Joined: Tue May 27, 2003 1:00 am
- Location: SHROPSHIRE UK
Re: Jampot Outer Tube - Too Far Gone? (1955 18CS)
How about fitting girling type inserts. They still look original but with improved damping