Gearbox adjuster
-
- Posts: 291
- Joined: Sat Jan 14, 2017 11:48 am
- Location: WEST MIDLANDS UK
Gearbox adjuster
Hope someone can shed some light on this for me. Started pulling the bike down to address some of the niggles. Got to order a few transmission parts, while compiling the list I remembered the gearbox adjuster. The one one the bike pushes the box forward. There isn't one to adjust backwards to tension the front chain. I've gone through the parts book again and would say that that is correct. There is a slot in the rhs engine plate just behind the top bolt. So it may be possible to retro fit one.
-
- Member
- Posts: 151
- Joined: Sun Sep 19, 2010 10:17 am
- Location: AUCKLAND NEW ZEALAND
Re: Gearbox adjuster
What you have is correct, the reaction of driving the rear wheel will pull the g/box rear ward. When adjusting the primary chain ensure the top bolt is up against the adjuster, I tapped the box back with a soft faced hammer.
- 1608
- Member
- Posts: 2496
- Joined: Mon Oct 05, 2009 1:00 am
- Location: ESSEX UK
Re: Gearbox adjuster
The adjuster is designed to move the gearbox back and forth. Adjust primary chain tension first ( approx 3/8" at its tightest spot) then tighten gearbox fixings. Then adjust rear chain tension ( 1-1/4" at its tightest spot and preferably with somebody sitting on the bike ( off its stand ) because the rear chain tightens up a bit when the bike is sat on.
-
- Posts: 291
- Joined: Sat Jan 14, 2017 11:48 am
- Location: WEST MIDLANDS UK
Re: Gearbox adjuster
Cheers. It would just be nice to have an adjuster for tensioning the chain rather than the way it needs to be done at the moment.
-
- Member
- Posts: 151
- Joined: Sun Sep 19, 2010 10:17 am
- Location: AUCKLAND NEW ZEALAND
Re: Gearbox adjuster
I thought the same, hopefully https://www.google.co.nz/search?q=norto ... 22#imgrc=_ works for you
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Gearbox adjuster
The tensioner does adjust the primary chain. You do need to slacken of the rear wheel and adjusters, and brake plate anchor so the rear wheel can move forward. Loosen gear box nuts and adjuster. Fit chain and tension via the adjuster, lock adjuster and tighten gearbox nuts. Reset rear chain adjustment etc.. Don't forget you had to loosen the rear brake anchor that also needs re tightening. Plus re adjust brake rod.
-
- Posts: 2884
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Gearbox adjuster
Hi
Or you can leave the rear wheel as is and just press down on the secondary chain lower run.
Regards Mick
Or you can leave the rear wheel as is and just press down on the secondary chain lower run.
Regards Mick
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Gearbox adjuster
If fitting a new primary chain, the gearbox would need to move forward, the rear chain will also need to move forward. Any alteration to the primary chain adjustment will effect the rear chain adjustment. You would need the primary chain to be quite loose to ease fitting the primary chain split link.
-
- Posts: 291
- Joined: Sat Jan 14, 2017 11:48 am
- Location: WEST MIDLANDS UK
Re: Gearbox adjuster
Thank you all. But there seems to be some confusion. I know how to do the adjustment. The adjuster on this box only pushes the box forward. To tension the chain you slacken the fixings just enough and knock it back. I'd prefer to use an adjuster that pulls and pushes the box. And as new chains are being fitted, now would be a good time to fit a different adjuster if it was possible.
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Gearbox adjuster
Well the system was used from pre war into the post war years on the bikes. Simply enough to do what it needed to do. In 62 years I have never had a problem. That more than satisfies me. By changing it you would need to declare the non standard fittings to your insurance company. For all insurance there is a question. Has the vehicle been changed from its standard specification.