Head stock bearing adjustment
-
- Posts: 36
- Joined: Wed Mar 21, 2018 5:11 pm
- Location: Highland UK
Head stock bearing adjustment
Hi apologies if this has been covered but is there any specific way of adjusting the above? Ie front wheel of the ground, wheel off etc. There is no steering damper fitted 58 csr frame and forks. Can't seem to get rid of a small bit of play.
Thanks in advance.
Thanks in advance.
Highlander, "There can be only one"…
-
- Posts: 2884
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Head stock bearing adjustment
Hi
Adjust with the front wheel off of the ground, exercise the bearing full travel left and right a few times and adjust to just discernable play - take it for a ride and repeat the procedure.
You should always feel the slightest play when pulling / pushing the front wheel, otherwise the bearing will be over tightened and degrade prematurely.
Regards Mick
Adjust with the front wheel off of the ground, exercise the bearing full travel left and right a few times and adjust to just discernable play - take it for a ride and repeat the procedure.
You should always feel the slightest play when pulling / pushing the front wheel, otherwise the bearing will be over tightened and degrade prematurely.
Regards Mick
-
- Posts: 36
- Joined: Wed Mar 21, 2018 5:11 pm
- Location: Highland UK
-
- Member
- Posts: 269
- Joined: Sun Apr 30, 2017 10:42 pm
- Location: ARGYLL UK
Re: Head stock bearing adjustment
I presume the same amount of play should be the objective when a dampener is fitted ie on '54 model.?
-
- Member
- Posts: 8598
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Head stock bearing adjustment
It's in just about every one of dozens of workshop manuals in Christians Archive.
http://archives.jampot.dk/book/Workshop ... dition.pdf
Here's a pic from the manual above of how to place a bike on a box with front wheel off the ground.
It'd be worthwhile spending time browsing the manuals in Christians Archive as they cover every maintenance task and answer just about every question ever asked
http://archives.jampot.dk/book/Workshop ... dition.pdf
Here's a pic from the manual above of how to place a bike on a box with front wheel off the ground.
It'd be worthwhile spending time browsing the manuals in Christians Archive as they cover every maintenance task and answer just about every question ever asked
You do not have the required permissions to view the files attached to this post.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Member
- Posts: 8598
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Head stock bearing adjustment
Do you know the history of your bike? Has someone rebuilt the forks/head stock?
Just a wild thought without knowledge of your bike's provenance...........
Inability to get the adjustment right could be due to having one too many balls in the head races. The correct number is one ball less than the number that will physically fit.
You 'can' fit 29 balls in each race but the correct number is 28.
See the manual, page 51 onwards re forks...
http://archives.jampot.dk/book/Owners_m ... ingles.pdf
Just a wild thought without knowledge of your bike's provenance...........
Inability to get the adjustment right could be due to having one too many balls in the head races. The correct number is one ball less than the number that will physically fit.
You 'can' fit 29 balls in each race but the correct number is 28.
See the manual, page 51 onwards re forks...
http://archives.jampot.dk/book/Owners_m ... ingles.pdf
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Member
- Posts: 8598
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Head stock bearing adjustment
Yes, but best to slacken it right off or it'll mask any play.Stephen G80 wrote:I presume the same amount of play should be the objective when a dampener is fitted ie on '54 model.?
Last edited by SPRIDDLER on Wed May 16, 2018 7:26 pm, edited 1 time in total.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
- REW
- Member
- Posts: 1369
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: CO DURHAM UK
Re: Head stock bearing adjustment
Having done 2 sets of head races this spring, one AMC the other er, Honda, I would say if you take the front wheel off the bike you will find it easier to assess the degree of play - because you are not fighting the weight of the front wheel. Similarly turning the bars left to right will show any notchiness due to worn races or tightness if you have over tightened.
Remember also to set the initial tightness slightly loose then nip up the lock nut at the top. It is surprising how that final tightening can soak up play, particularly on a modern bike setup.
Also, don't forget to loosen the bottom yoke pinch bolts before you try to adjust the steering bearings or the job is impossible. And tighten them last too.
Finally, if you knew any or all of this, apologies!
Remember also to set the initial tightness slightly loose then nip up the lock nut at the top. It is surprising how that final tightening can soak up play, particularly on a modern bike setup.
Also, don't forget to loosen the bottom yoke pinch bolts before you try to adjust the steering bearings or the job is impossible. And tighten them last too.
Finally, if you knew any or all of this, apologies!
Ron
1951 Matchless G3L thumping round the Durham Dales.
1951 Matchless G3L thumping round the Durham Dales.
-
- Member
- Posts: 8598
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Head stock bearing adjustment
Quite so, Ron, but it's all in detail in the manuals and I couldn't be ar*sed to type any more out.
I'm keen that youngsters (average age of Club members is 67 and rising) know where to find the information as we old sages won't last forever, unlike our bikes.
I'm keen that youngsters (average age of Club members is 67 and rising) know where to find the information as we old sages won't last forever, unlike our bikes.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
- REW
- Member
- Posts: 1369
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: CO DURHAM UK
Re: Head stock bearing adjustment
'Course we will, we're baby boomers!SPRIDDLER wrote: we old sages won't last forever, unlike our bikes.
Ron
1951 Matchless G3L thumping round the Durham Dales.
1951 Matchless G3L thumping round the Durham Dales.